2008 Infiniti EX35 - Brake Control System (Section BRC) (113 pages)
Download Brake Control System (Section BRC)
Manual Description
DIAGNOSIS AND REPAIR WORK FLOW 4, cONTROL UNIT : Special Repair Requirement 8, nEUTRAL POSITION : Special Repair Requirement 8, aND ELECTRIC UNIT (CONTROL UNIT)] 30.
POWER AND GROUND SYSTEM 41, aBS MOTOR, MOTOR RELAY SYSTEM 44, c1126 IN ABS SOL 53, c1127 OUT ABS SOL 55.
YAW RATE/SIDE G SENSOR 63, bRAKE FLUID LEVEL SWITCH 71, cAN COMM CIRCUIT (ICC UNIT) 75, pOWER SUPPLY AND GROUND CIRCUIT 76.
Wiring Diagram - BRAKE CONTROL SYSTEM - 90, aBS FUNCTION DOES NOT OPERATE 100, (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 104, fRONT WHEEL SENSOR : Exploded View 107.
FRONT WHEEL SENSOR : Removal Installation 107, rEAR WHEEL SENSOR : Exploded View 108, rEAR WHEEL SENSOR : Removal Installation 108, fRONT SENSOR ROTOR : Exploded View 109.
FRONT SENSOR ROTOR : Removal Installation 109, rEAR SENSOR ROTOR : Exploded View 109, rEAR SENSOR ROTOR : Removal Installation 109, dIAGNOSIS AND REPAIR WORK FLOW.
If steering angle sensor, steering system parts, suspension system parts, ABS actuator and electric unit (control unit) or tires have been replaced, or if wheel alignment has been adjusted, be sure to adjust neutral position of steering angle sensor before driving, get the detailed information from the customer about the symptom (the condition environment when, the incident/malfunction occurred) using the diagnosis work sheet, check the DTC display with self-diagnosis function.
Perform the diagnosis applicable to the displayed DTC, check that the symptom is a normal operation that is not considered a system malfunction, is the symptom normal operation, check that the warning lamp indicator lamp illuminate.
ABS warning lamp: Refer BRC-81, "Description", brake warning lamp: Refer BRC-82, "Description", vDC OFF indicator lamp: Refer BRC-83, "Description", sLIP indicator lamp: Refer BRC-84, "Description".
Perform the diagnosis applicable symptom, repair or replace specified malfunctioning parts, perform the self-diagnosis again, and check that the malfunction repaired completely, is no other DTC present repair completed.
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT, aDDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description, after replacing the ABS actuator and electric unit (control unit), perform the neutral position adjustment, aDDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Requirement.
Perform the neutral position adjustment for steering angle sensor, >> Refer to BRC-8, "ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION : Special Repair Requirement", aDJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION, aDJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION : Description.
When doing work that applies to the list below, make sure to adjust neutral position steering angle sensor, adjustment of steering angle sensor neutral position, removing/Installing ABS actuator and electric unit (control unit), replacing ABS actuator and electric unit (control unit).
ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION : Special Repair Requirement, to adjust neutral position of steering angle sensor, make sure use CONSULT-III, (Adjustment cannot be done without CONSULT-III.
Manual Description
DIAGNOSIS AND REPAIR WORK FLOW 4, cONTROL UNIT : Special Repair Requirement 8, nEUTRAL POSITION : Special Repair Requirement 8, aND ELECTRIC UNIT (CONTROL UNIT)] 30.
POWER AND GROUND SYSTEM 41, aBS MOTOR, MOTOR RELAY SYSTEM 44, c1126 IN ABS SOL 53, c1127 OUT ABS SOL 55.
YAW RATE/SIDE G SENSOR 63, bRAKE FLUID LEVEL SWITCH 71, cAN COMM CIRCUIT (ICC UNIT) 75, pOWER SUPPLY AND GROUND CIRCUIT 76.
Wiring Diagram - BRAKE CONTROL SYSTEM - 90, aBS FUNCTION DOES NOT OPERATE 100, (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 104, fRONT WHEEL SENSOR : Exploded View 107.
FRONT WHEEL SENSOR : Removal Installation 107, rEAR WHEEL SENSOR : Exploded View 108, rEAR WHEEL SENSOR : Removal Installation 108, fRONT SENSOR ROTOR : Exploded View 109.
FRONT SENSOR ROTOR : Removal Installation 109, rEAR SENSOR ROTOR : Exploded View 109, rEAR SENSOR ROTOR : Removal Installation 109, dIAGNOSIS AND REPAIR WORK FLOW.
If steering angle sensor, steering system parts, suspension system parts, ABS actuator and electric unit (control unit) or tires have been replaced, or if wheel alignment has been adjusted, be sure to adjust neutral position of steering angle sensor before driving, get the detailed information from the customer about the symptom (the condition environment when, the incident/malfunction occurred) using the diagnosis work sheet, check the DTC display with self-diagnosis function.
Perform the diagnosis applicable to the displayed DTC, check that the symptom is a normal operation that is not considered a system malfunction, is the symptom normal operation, check that the warning lamp indicator lamp illuminate.
ABS warning lamp: Refer BRC-81, "Description", brake warning lamp: Refer BRC-82, "Description", vDC OFF indicator lamp: Refer BRC-83, "Description", sLIP indicator lamp: Refer BRC-84, "Description".
Perform the diagnosis applicable symptom, repair or replace specified malfunctioning parts, perform the self-diagnosis again, and check that the malfunction repaired completely, is no other DTC present repair completed.
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT, aDDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description, after replacing the ABS actuator and electric unit (control unit), perform the neutral position adjustment, aDDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Requirement.
Perform the neutral position adjustment for steering angle sensor, >> Refer to BRC-8, "ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION : Special Repair Requirement", aDJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION, aDJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION : Description.
When doing work that applies to the list below, make sure to adjust neutral position steering angle sensor, adjustment of steering angle sensor neutral position, removing/Installing ABS actuator and electric unit (control unit), replacing ABS actuator and electric unit (control unit).
ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION : Special Repair Requirement, to adjust neutral position of steering angle sensor, make sure use CONSULT-III, (Adjustment cannot be done without CONSULT-III.
Read(view) online free pdf manual 2008 Infiniti EX35
Infiniti Models